Red Tape on All 3-Pronged Electrical Tools & Extension Cords on 7/1/13!

Good morning to all I.D.I. employees:  All Safety Coordinators should have been provided a roll of red electrical tape.  We begin a new quarter on Monday, 7/1/13 for our Assured Grounding Program.  You are to inspect, test and color-code with red tape all 3 pronged electrical tools and extension cords.  All electrical tools and cords need to be visually inspected.  If you see any defects in the cords such as bare wires, severe kinks, missing or damaged ground prong, the cord pulling away from the plug end housing, etc., then that tool or cord would need to be immediately removed from service and reported to the lead person.  If your tool/cord passes the visual inspection, your next step is to test the cord with a receptacle tester.  First, you should test the oulet that you will be plugging your cord into to ensure that it is properly wired.  You should see 2 yellow lights lit up on your tester and the red light should be off.  This means the outlet is working appropriately.  Next, plug your cord into the outlet and then test the cord with the receptacle tester.  Again, you should see the same light pattern as mentioned above and this would mean the cord passed the test and it is good and safe to use.  Any other light pattern means that there is a problem with the cord and the cord needs to be removed from service and reported to your lead person.  If the cord passes the visual inspection and the cord tester test, you should then remove the previous quarter's green electrical tape and install the red electrical tape about 1" down from both plug ends.  Your cord is now in compliance with our 3rd quarter's Assured Ground Program.  The red tape shall remain in place from 7/1/13 through 9/30/13.  You are not quite done yet!  You now need to visually inspect all electrical cords and tools on a daily basis and if any defects are found, the cord needs to be immediately removed from service.  Thank you for taking the time to ensure your electrical tools and cords are in safe working order.  Your actions may prevent one of our family members from sustaining an electrical shock type injury or worse yet and electrocution.  If you have any questions regarding our Assured Grounding Program, please call our Safety Director, Peter Graham, at (847) 417-1689.

Have a Safe Day!

Employees With Their OSHA 30-Hour Card (Current Within The Past 3 Years!)

Good afternoon to all I.D.I. employees:  Over the past few years, we have been encouraging our employees to enroll in the OSHA 30-hour Construction Safety Course.  Many general contractors that we work with require that we place employees at their projects that have their OSHA 30-hour card current within the past 3 years.  Today, we want to recognize our employees that have taken the OSHA 30-hour course and that are current within the past 3 years.

We have 15 employees in this high standard category and they are:  Jesse Aguirre, Paul Baca, Earl Bingman, Cesar Chavez, Daniel Dominick, Angel Flores, Chris Frankowski, Brian Frederick, Tom Gracyk, Praxedes Lagunas, Adam Lichon, Gary Newton, Jason Ondera, Chris Pickrum and Adalberto Suarez.

Congratulations to all of you on successfully completing this course.  The OSHA 30-hour course is a huge time commitment and we know it.  By taking this course, you have demonstrated with your actions, your commitment to the company, to your Superintendent and to yourself and you have showed us what you are all about.  We also have several other employees that have taken the OSHA 30-hour course, however, they are not current within the past 3 years.  The OSHA 30-hour card never expires but many general contractors set a 3-year current standard.

Why should you enroll in the OSHA 30-hour Construction Safety Course?  For starters, this course provides a good solid foundation of safety training.  You will be provided with 30 hours of construction safety training that can help you to sustain a long-term healthy & injury-free career in the construction field.  This course may just save your life!  The OSHA 30-hour course is not just good for you as far as work goes as it teaches invaluable life skills that you can take with you and use anywhere for the rest of your life as this card never expires.  This course also looks terrific on a trade person's resume.  Many employers are getting choosier when it comes to seeking out new hires and having your OSHA 30-hour card is what may make you the front runner.

Another reason we are encouraging participation in an OSHA 30-hour course is that we are bidding work to general contractors that require us to man their projects with employees that have taken this course.  By taking this course, you make yourself more valuable to a Superintendent when they are choosing their work crews for various job sites.  I also want to mention that if you do take this course; that it does not guarantee that you will work.  It does however increase your chances especially in the weak economy that our country is currently in.  

Where can I take this course you ask?  The OSHA 30-hour is offered by your union trade schools to members in good standing.  Also, if you take the course through your union trade school, we understand that it is either free or low cost to members.  It is offered at limited times throughout the year.  If you are interested in signing up, you are encouraged to contact your trade school by phone or you can look them up on the internet to see when the course is offered.  You can also take it online through some internet services.  We recently negotiated a $159.00 price for the course through Grainger.  If you choose to take the course online through Grainger, please contact our Grainger Territory Sales Representative, James Gill, Jr. at (224) 216-0986 to get the $159.00 pricing and he will advise you how to get signed up for the course.  If you are going to proceed with taking the OSHA 30-hour online, make sure you enroll in the OSHA 30-hour construction course and not the OSHA 30-hour general industry course.  If you have any questions about taking the course online, you can always contact our Safety Director, Peter Graham and he can provide you with more information to help you.  You can reach Peter by e-mail at pgraham@4idi.com.  After you take the OSHA 30-hour, you will be issued a card sometime around 30 days later. Please provide our Safety Director with a copy of your card so we know that you took the course.

Lastly, if you have taken the OSHA 30-hour course and if you have not provided us with a copy of your card, please send a copy of your card to Peter Graham so we can document this on your I.D.I. safety record.  

Make yourself standout in the crowd!

Have a Safe Day!

It's Monday Morning - Time for a Safety Toolbox Talk!

Good morning Safety Coordinators:  Today is Monday which means it's that time of the week to perform a weekly job site safety inspection and to perform a meaningful toolbox talk with our employees around 9:45am.  Let's start the week off on the right foot for the benefit of our employees.  Some time between 7:00am and 9:00am this morning, all Safety Coordinators should grab a safety inspection form from your Safety Coordinator manual and walk your job site and look for hazards.  Any hazards found should be documented on your safety inspection form and comments about the hazard and plan to protect our employees from the hazard should be documented.  Then after your morning break, at 9:45am, the Safety Coordinators should gather the crew and perform a toolbox talk that is pertinent and meaningful to the tasks being performed, the equipment being used or to something that pertains to safety at your job site.  Then after the toolbox talk has been completed, have all the employees at the project that participated in the toolbox talk sign the toolbox talk roster.  Finally, the Safety Coordinator should advise the employees of any hazards found during the walk around safety inspection and what our plan is to abate the hazard and to protect the employees from the hazard.  If a hazard is identified that cannot be abated immediately, you should then contact our Safety Director, Peter Graham, to discuss it so we can implement a plan to abate the hazard.  After the above is completed, please do your best to get the toolbox talk sign in roster & safety inspection form turned in to our Safety Department no later than Friday, 6/14/13.  Lets make it a goal to get 100% of the toolbox talks rosters and safety inspection forms turned in by Friday. If you have any questions, please contact our Safety Director, Peter at (847) 417-1689 or you can e-mail him at pgraham@4idi.com.

Thank you for helping us to prevent injuries to our employees.  Go Hawks!

From the "I Caught You" Series

At International Decorators, we have a habit of catching our employees performing safely! Below are a few action shots of our employees being caught in action performing in a safe manner or showing something they did for the safety of our employees.

Great job everyone!  You are helping us to live up to our safety mission statement which is:

"Everyone Goes Home Alive and in the Same Condition as They Arrived; Your Loved Ones Count On It."

This stairwell scaffold was built like a tank by Keith Rehn.
Wall to wall 3/4" plywood decking on top of 6 aluminum planks, etc.  Great job - Keith!

Same scaffold, just another view

One last view of the same scaffold from underneath

Can I build a scaffold or what!  Great job - Keith!

Salvador Rodriguez, taping walls in a safe manner and wearing the correct PPE for the job.
This guy is so confident with his taping abilities that he wears a $200.00 shirt while taping as he knows all the mud is going on the wall only.  

A couple of I.D.I.'s finest performing housekeeping and game planning.
Great job also with wearing the appropriate PPE - Joe Vess, Cesar Chavez and Jaime Martinez

Taper, Fernando Rodriguez tying off with fall arrest equipment while working in an elevator shaft.
Is this guy ever not smiling?  Great job - Fernando!

Lead Interior Framing Supervisor, Dan Hilt & Superintendent, Brian Haese -
Doing some serious thinking & planning at the O.C.C. project.  While doing so, they are wearing the appropriate PPE for a construction project.  Great job - gentlemen!

National Electrical Safety Month: Six Safety Tips for Working Near Overhead Power Lines!

In honor of National Electrical Safety Month this May, spark a safety-conscious conversation by sharing these six tips for working near overhead power lines.

It was just a typical day at work. Gary Norland and his coworkers were discussing weekend plans as they worked near overhead power lines. But when Norland leaned back and came into contact with 12,500 volts of electricity, he suffered life-changing burns the required a 4-month hospital stay and more than 50 surgeries.

Now, 20 years after the accident, Norland has a message: “If you get injured, it's an impact that's going to affect everybody.”

During National Electrical Safety Month this may, Norland and his family are working with Safe Electricity's “Teach Learn Care TLC” campaign to help prevent others from having accidents with overhead power lines and to keep other families from having to go through such a tragic experience.

“Those small shortcuts will add up to that big one, and then everything is going to change," Norland explained. “Take the time, and do it right the first time. Make sure you do everything safe.”

Safe Electricity, a public awareness program of the Energy Education Council (EEC), offers the following six tips for those who may be near overhead power lines when working outside:

1. Look up and around you. Always be aware of the location of power lines, particularly when using long tools like ladders, pool skimmers, and pruning poles. Be especially careful when working near power lines attached to your house. Keep in mind that wind can blow large objects out of your control.
2. Keep equipment and your body at least 10 feet from power lines. Even if you do not come in contact with a power line, the electricity can arc to nearby objects and people.
3. Be careful when working on or around your roof. That includes installing or cleaning gutters, installing rooftop antennas and satellite dishes or doing repair work. Never use water or blower extensions to clean gutters near electric lines. Contact a professional maintenance contractor.
4. Never climb trees near power lines.
5. Never trim trees near power lines. Leave that to the professionals.
6. Always follow safety procedures, no matter how boring and mundane they seem.

“We are grateful that Gary and his family are willing to share their difficult experience to help prevent other tragic accidents," said Molly Hall, executive director of the Safe Electricity program. “We encourage everyone to visit SafeElectricity.org to see the video of Gary's story and learn more about staying safe around overhead power lines.”

Citation:  The above article is from EHS online magazine and the author is Laura Walter, 5/13/13.

Have a Safe Day!

100% Attendance at our Painters & Tapers Only Quarterly Safety Meeting!

As most of you know, we held a volunteer quarterly safety meeting on April 20th for the painters and tapers only.  The safety training topics included respirator training, fit testing on the respirators and stilt safety.  We wanted to report out to everyone that for the first time since we began tracking the attendance, we had a 100% show-up rate.  

We hope that the safety training session was beneficial to everyone in attendance. We had excellent participation and questions during the session.  We want to thank all of you for taking time out of your busy lives for the sake of your safety.  The main reason we provide safety training is because of you and our company's safety mission statement - "Everyone Goes Home Alive and in the Same Condition as They Arrived; Your Loved Ones Count On It."  

During the meeting, we also celebrated the story of our employees that saved a plumber's life. We had a crew working at a downtown tenant space on 4/12/13 and a plumber suddenly dropped to the ground.  He was unconscious and at times, not breathing.  Our very own employees, Gabe Macias and Tom Gracyk immediately began performing CPR on the plumber. Also assisting in the emergency situation was Jim Woods, Paul Baca, Joe Bellich, Rick Rizzi and Randy Francisco.  In the end, we found out that the plumber had a massive heart attack. He has had bypass surgery and we were told that he is doing well.  We were also informed that our employees saved his life.  The CPR kept him alive until the paramedics arrived!  What an awesome team effort and great work under some extreme pressure!

What about you?  Are you trained on CPR?  Are you prepared to save a life?  Will you be ready to step in when someone literally needs you to save their life?  If you have not been trained in CPR, please contact Safety Pete at 847/417-1689 and he could provide you with information on how to get trained in CPR or contact your union to obtain this training.  Below is the contact information for your respective unions:

            Painters District Council #14:  www.pdc14.com                     312/421-0046

            Painters District Council #30:  www.paintersdc30.com           630/377-2120

            Chicago Carpenters:               www.chicap.org                      847/364-8367

We urge you to be prepared like Tom & Gabe are!  Don’t forget to give your family an extra hug & kiss tonight!

Below is a video from the quarterly safety meeting celebrating the story! Below that is another video showing the painters being fit tested on their respirators by Luis Moctezuma of 3M and some photos taken during the safety meeting.

I.D.I.'s President, Butch - demonstrating how in the old days, some employees would wear a dust mask and punch a hole in it so they could smoke a cigarette.  This was obviously not condoned at the time and no one does this anymore!

Type of Respiratory Protection for Lacquer Paint Applications!

As you all know, we had a volunteer quarterly safety meeting on Saturday, 4/20/13 with our painters and tapers and the main topic of the meeting was respiratory protection.  During the meeting we were discussing respirator cartridge filters, the types to use and when to use them, etc.  One of our very fine painters,Vito Rizzi asked the following question:  "What type of cartridge filter should be used for applying lacquer type paints."  We encourage these types of questions as we can all learn from them.  So first of all, thank you, Vito, for asking the question.  According to the material safety data sheets and according to 3M, which is our respirator cartridge filter provider, the correct cartridge filter to use for lacquer paints is the organic vapor cartridges.  These are the black labeled cartridges that we are already using for our common paint spray applications.  These black labeled organic vapor cartridges are the correct respirator filters to use for most paint applications.  They are used for latex, lacquers, enamels, most epoxy's, solvents and many other varieties of paints.  Applications that would typically require a different type of cartridge filter other than the black labeled organic vapor cartridge are ammonia, acids, chlorine, etc.  The material safety data sheets will typically tell you the type of cartridge filter to use.  The MSDS will typically say to use an organic vapor cartridge which is the black labeled one.  If you are reviewing an MSDS sheet and it says to use a cartridge other than an organic vapor cartridge, then I would advise you to contact our Safety Director, Peter Graham.  I (Peter) am always reviewing the MSDS sheets when we are using a new product that we are not familiar with.  If we provide a paint product that calls for a different type of respirator cartridge filter, we would notify our paint crew that will be using the product and provide them with the correct cartridge filter.

I hope this answers the question.  As always, please contact our Safety Director, Peter Graham with any safety related questions.

Have a Safe Day!